Waterproofing PaintsBitumen Roof Seal
View product
Waterproofing PaintsEnfleks Waterproofing Coating (Fibre-Reinforced)
View product
Waterproofing PaintsEnfleks Waterproofing Coating (Without Fibre)
View product
Waterproofing PaintsEnlastic Waterproofing Sealer
View product New
Waterproofing PaintsTCP Waterproof Spray – Leak Filler
View productWaterproofing in Ghana
Water is the main enemy of roofs, walls and foundations in Ghana, especially in the rainy season. TCP’s waterproofing range covers the common jobs. Enlastic is a flexible black bitumen-based product for roofs, walls, foundations, basements, bathrooms and terraces. Enfleks is a white acrylic waterproofing paint, available with or without fibre reinforcement, for roofs and walls. TCP Waterproof Spray is an aerosol leak filler for small repairs on gutters, metal roofs and wall cracks, and TCP Roof Seal is an aluminium-backed tape for sealing leaks, cracks and seams.
The right choice depends on the surface, how much the structure moves and how exposed the area is to sun and water. Our teams in Accra and Kumasi can help you choose, estimate quantities from your measurements and explain how to prepare and apply each product. Always follow the technical sheet.
Which waterproofing product for which job
Flat concrete roofs, terraces, foundations and basements: Enlastic is a flexible bitumen-based membrane that bridges cracks up to 5 mm. It comes in a 17 kg pack and covers about 1 kg per m² for each millimetre of thickness. Prime with Enprimer, leave 24 hours between coats and allow one week before the surface meets water. On roofs, protect it from direct sunlight with a suitable covering.
Roofs and walls that should stay white: Enfleks is a white, elastic, breathable acrylic coating in an 18 kg bucket, sold with or without fibre reinforcement. Prime with the product diluted 50% with water and apply at least two coats. The system consumption on the data sheet is 2.5 L/m² against ground moisture, 4.0 L/m² against temporary water pressure and 5.5 L/m² against continuous water pressure, with glass-fibre mesh between coats for the last two. It hardens in 24 hours and needs at least 7 days to dry fully.
Small leaks in gutters, metal roofs and wall cracks: TCP Waterproof Spray is a 450 ml aerosol leak filler for gaps narrower than 2 mm. It is tack-free in 20 to 35 minutes and dry in about 24 hours.
Seams, joints and quick repairs: Bitumen Roof Seal is an aluminium-backed tape, 1.5 mm thick, in rolls 5, 7.5 or 10 cm wide and 10 m long. Press it onto a clean, dry surface.
Before you start
Waterproofing fails most often because of the surface, not the product. Work on a sound, clean and dry surface, remove dust, oil and loose material, and plan the job for dry weather. In the rainy season, check the forecast for the drying time of the product you choose. Reinforce cracks and areas under water pressure as the data sheet describes.
Common questions
Which product should I use on a concrete roof?
Enlastic and Enfleks are both made for roofs. Tell us the roof type and condition and we will recommend one.
How much do I need?
Coverage depends on the product: Enlastic is about 1 kg per m² for each millimetre of thickness, and Enfleks about 1 to 2 m² per litre per coat. Send us your measurements and we will calculate it.
How do I work out the quantity?
Measure the area in square metres and multiply by the consumption above for your situation. For Enlastic at 2 mm thickness, a 17 kg pack covers about 8.5 m². Send us the measurements and we will check the figure with you.
Can I use these products in a bathroom?
Enlastic lists bathrooms among its uses. Tell us what will go on top (tiles, screed) so we can advise on the order of work.
Where can I buy waterproofing in Ghana?
At the TCP showrooms in East Legon, Accra, and Ahinsan, Kumasi, or by sending an enquiry from this page.






